Page History

...

Design pressure: 1500 psi

Sustainer:

Aluminum Case: OD: 4", ID": 3.62575" (thickness 31/168")

Phenolic Liner: OD: 3.75", ID: 3.5" (thickness 1/8")

Casting Tube: OD: 3.6255", ID: 3.375" (thickness 1/816")

Booster:

Aluminum Case: OD: 6", ID: 5.5625" (thickness 13/416")

Phenolic Liner: OD 5.5625", ID: 5.25375" (thickness 1/8")

Casting tubeTube: OD: 5.25375", ID: 5.12525" (tickness thickness 1/16")

Constraints:

• manufacturing Manufacturing capability
  • lathes Lathes can machine up to 6" diameter
• available Available liners' specs (lengths)
  • 48", 53.1", 59.1", 65"
• need Need for a casting tube within liner
  • unless Unless multicast in one liner is feasible
    • While potentially feasible
• available tube size
• • • , many have told us it is better practice to use a casting tube with each grain in sections with o-rings in between each ring
• Available tube size
• Tolerances of the tubes are not within rocketry tolerance (+-.001")
  • Solution: Use a simulator piece while machining the parts to achieve as good of a seal as possible
    
    • Simulator piece is a cut piece of the case stock. Get part to nominal diameter then test fit with simulator until it fits by hand
    • Use 300 or 400 series o-rings to hold a better seal.

Design Specs:

• 6' ish " OD
• Internal pressure expected to be around 1500-2000 1000 psi max
• Safety factor 2
• min. thickness: 0.350"

Motor Case:

• 1.5
• Thickness: 3/16"
• order from Speedy Metals? (lengths: 1', 2', 3', 4', 6', 8')
• 1/2" thick
• ID: 5.25', OD: 6'

Phenolic Tubes:

• order Order from Franklin Fibres (lengths: 48", 53.1", 59.1", 65")
• 1/8" thick for liner
  • ID: 5.25'375.", OD: 5.5'625"
• 1/16" thick for casting tube
  • ID: 5.125'25", OD: 5.25'375"
• long lead times, order in bulk this semester

Bolts:

2 rows of 16x 1/4-20 bolts.

Total of 64 bolts on the booster.

...

• available liners' specs (lengths)
  • 48", 53.1", 59.1", 65"

Design Specs:

• 4' ish OD" OD, 3.75" ID
• Internal pressure expected to be around 1500-2000 300 psi max
• Safety factor 23
• min. thickness: 0.241" - closest thickness is 0.25"Thickness: 1/8"

Motor Case:

• order Order from McMaster or Online Metals
• 1/28" thick
• ID: 3.575', OD: 4'

Phenolic Tubes:

• order Order from Franklin Fibres (lengths: 48", 53.1", 59.1", 65")
• long lead times, order in bulk this semester
• 1/8" thick for liner
  • ID: 3.5", OD: 3.75"
• 1/16" thick for casting tube
  • ID: 3.
  25'
  • 375", OD: 3.5
  '
  • "
• long lead times, order in bulk this semester

Bolts:

1 rows of 8x 10-20 bolts.

Total of 16 bolts on the sustainer.

Case calcs done using 2000 1800 psi as internal pressure

Thin vs Thick Case Assumption: thin case assumption can be used if  

...

Calculated with thin case assumption -> safety factor = 2, case thickness = 0.371"Move onto thick case assumption -> safety factor = 21.5, case thickness = 0.350191"

Sustainer

Sustainer thin case assumption if t < 0.2"

...